Weight gain of the structure, due to the use of concrete and cement slurry, in flooring products or wall cover and create a thick layer when installing
Failure to observe the standard ratio in concrete and non-weighing materials and by that, the weaker drying of products to the wall or floor and product separation, if inappropriate installation
Inability to install products such as granite and marble due to low water absorption and... and replacing these high quality products with poor quality products such as travertine stones
Concrete aggregate problems over time and the difference in the coefficient of expansion and contraction of the concrete used with the installed products and after a while, the product is detached from the wall or the floor
The inability to install various products, by concrete and slurry and on surfaces such as plaster, tile and old ceramic
Failure to repair damaged products due to the formation of thick layers
In slurry and installation with slurry, creating a poor adhesive binder (concrete), due to the use of high amounts of water during construction, as well as the use of cement powder for priming and...
Inability to suitable balance, as well as product separation on wall covers, because of the slurry pressure behind the product due to the high thickness of concrete used
High water absorption in installation with ordinary concrete, for facades or flooring outside the building and the influence of moisture on the inner wall in the facades and product separation on flooring and...
And many more...
But in the installation with construction adhesives, the above problems and many other problems that are not mentioned can be covered. In the country, there are many manufacturers of adhesives for construction. therefore, many of these companies, because of unreasonable competition, and lower prices, for the purchase of brokers, ignore many of the polymer and mineral materials, which are required in adhesives. 
These companies also use low quality minerals and polymer to produce lower-cost products, which is in the interests of brokers, and it will not benefit for producers and consumers. therefore, HUNAM Artificial Stone Group has been offering a variety of high quality Megafix construction adhesives, which we will introduce some of them below.
Powder tile adhesive:this product can be used to install bricks, antique stones, artificial stones, Installation of tile and flooring ceramic, in areas where permanent moisture is in contact (or not) with the exception of gypsum walls or with ceramic and tile surfaces (if you use concrete glue, you can also use it for these places), can be used
Megafix powder tile adhesive is available in 20kg package.
The Megafix powder tile adhesive is available in five modes:
Tile adhesive with gray color, gray tile adhesive with fibers, white powder tile adhesive, as well as powdery tile adhesive with white fibers, powder tile adhesive of pool
Dough Tile Adhesive:
Tile adhesive for installation of antique stones, natural stones, facade bricks, ceramic and floor tiles and walls, local remedy, install antique or ceramic tile on surfaces such as ceramic and tile or old stone... and, in general, places that are not in contact with constant humidity can be consumed.
Megafix Dough Tile Adhesive is available in packages of 12 and 15 kg.
Concrete adhesive:
Megafix concrete adhesive is used to create various properties such as high adhesion, decrease in water absorption, creating higher elasticity and bending resistance and ... in concrete and also in powdered adhesives, can be used
Megafix concrete adhesives can be supplied in packages of 20 kg and 12 kg.
megafix shiny resin: to protect against acid rain and sunlight as well as shine and creating a better color effect in natural stones, artificial stones, facade bricks, antique stones and travertine stones are used.
Megafix protective resin, is available in one-liter packaging.
Nano Megafix facade protector: This Nano material is used to reduce the absorption of natural stone and travertine and artificial stone, as well as to reduce water absorption of bonding lines.
Developed artificial stone (Artificial Stone Cultured Marble & Granite), from variety of minerals of about 50-80%, and acrylic polymers with specific characteristics of about 47-17% and Nano materials of about 3%, is formed, which has made it possible to produce and construct surfaces, for various uses, and unique features.
the polymer materials used in these products, in addition to preserving the resemblance to natural marble and granite, the final product is stronger than natural stones in terms of water resistance, strong detergent and acids, and in terms of flexural strength and compression strength. also, using this product, it is possible to design and manufacture, in various shapes, for interior decoration of the building.
artificial marble and granite similar to coreen, or cultured marble-granite and solid surface, are polymer and Nano integrated surfaces, which has various applications in the building industry, including designing and manufacturing of various counter top stones and kitchen cabinets, stones for use in bathrooms and toilets, including bathtubs and jacuzzi - washbasin sinks, stones under the shower, types of sinks, laboratory counter - health centers - hospitals and banks - stone stairs indoor decoration - types of wall coverings in the building - wall covering between the cabinets, and...
The materials in the structure of granite and marble plates are covered by an impervious polymer surface, and because of this, it is resistant to the penetration of a variety of fungi and bacteria, color spots, strong detergents, and acids ...
Due to the presence of Nano resins, in the molecular composition of the plates, they have the ability to hit, and have very high physical resistance. the surface of the plates is very robust and sturdy and have high endurance against impact, pressure, fracture and cracking. however, it is easy to repair and recover in the event of any damage to the operation and installation process of the product or the method of use.
Levels of Artificial marble plates similar to coreen of HUNAM company, is very glossy and polished and consumers are satisfied. HUANM marble manufacturers company, is proud to be entering the new phase of product development, gravestone (marble tombstone and artificial granite), which in solidity and beauty are mixed together. artificial tombstones, produced in ready form, can be installed. is available in two design.
Application of Artificial Stone Marble and Granite of HUNAM company:
Types of artificial stone cabinets
Types of artificial stone and public bathroom sink
Counter-top and table stone laboratory
Types of kitchen sinks
types of marble & granite cabinets stone
Types of artificial stone countertop
Types of office counters - banks - health centers and stores and...
And many other items
Feature of marble and artificial granite products similar to coreen:
Surface integrity is made in the stones, pelvis and corneas
Smooth surface with light reflection and variety of colors and effects
Completely antibacterial level and resistant
20 to 30% lighter and more resistant than natural stone
Artificial engineering stone water absorption coefficient less than 0.1%
Non-Sedimentation in artificial engineering stone
High resistance of artificial engineering stone, against acidic and alkali materials
Ability to wash artificial engineering stone, with any standard detergent
Possibility to produce integrated stone, up to 4 meters long and more
High resistance to artificial engineering stone, against impact and scratches and in the event of a problem, the ability to repair the product
Preserving transparency of artificial granite marble stones in long term
Stone resistance, against indirect heat, up to 240 degrees Celsius
designs of sink, available:
polymeric artificial stone sink cultured marble-granite and solid surface: selling sink in bulk and crumbly
WC stone sink - Artificial Stone Coreen Sink / sink sale
One of the problems of the production of artificial stone of cement plast, as well as concrete, especially in winter and cold weather, is the increase in the duration of processing, or the drying of concrete or artificial stone. therefore, to accelerate the hydration and polymerization reactions, it is possible to use early hardening Nano
Also, using this article, you can achieve results such as:
An increase of about 5 to 15% of the surface erosion of the product (Assuming that the amount of cement used is fixed, according to the fixed formula and also with the dose of this substance) this material (Nano flood accelerator)
It increases the flexural strength of the product by 10 to 20 percent, as compared to the previous formula (Due to stronger crystallization and more in cement)
It reduces the duration of the concrete's final strength (The final strength of the product is after 28 days) depending on the dose, this period is reduced to 10-14 days
Increasing the compressive strength of products by 10-20% compared to the previous formula
Due to the presence of Nano materials in intermolecular bonds, it reduces surface and absolute water absorption of the product according to the amount of consumption (20-30% reduction in product water absorption than constant formula)
Increasing the frost resistance due to the filling of continuous and discontinuous cavities in the product tissue
More glossy product due to reduced processing time and accelerated product curing process
Physical properties of early hardening Nano product of artificial stone cement plast:
Concentrated suspensions of calcium silicate hydrate nano-particles are white
This material is without chlorine ion, as well as without impact on the priming of concrete and artificial stone cement plast
PH = 11-12
The mechanism of early, hardening nanosil behavior (accelerator) on artificial stone cement plast:
When the cement is combined with water (the hydration reaction), the nano-particles of calcium silicate hydrate are large in size between the particles of the cement and act like a bud in the cement
Calcium silicate hydrate (early hardening nanosil) resulting from hydration of cement grows on these buds, in other words, all the cement particles start to simulate and reproduce in an intelligent manner at once. and thus leads to a tightening and secondary fixation in concrete and artificial stone cement plast.
Amount of consumption early hardening nanosil artificial stone cement plast
The consumption rate is based on the different weather conditions and the storage temperature of the product to the variable processing and between 2 to 5 percent for the artificial stone cement plast and between 1 and 4 percent for the concrete.
Conditions for the storage conditions of early hardening nanosil of concrete and artificial stone:
At temperatures above 5 ° C, and away from direct sunlight, it will be between 9 and 10 months
How to use early hardening nanosil of artificial stone cement plast:
Due to weather conditions, and the storage temperature of the product until the curing of the concrete or artificial stone cement plast, the amount of 1 to 5% is added when adding water to the mixture.
this material It has no effect on initial tightening
Advantages of early hardening nanosil of artificial stone cement plast:
Reduce the duration of concrete curing and drying concrete
Reduce curing time in artificial stone cement plast in the summer and especially in the winter (Minimum storage time is between 8 and 10 hours in winter)
Decrease the opening time of artificial stone cement plast from the mold in the winter from at least 24 hours to a maximum of 10 hours
Due to increased speed of hydration and polymerization, the product is treated earlier and prevents adhesion of materials to molds.
Low grade cement converts to high grade cement in terms of strength and hardness
Ability to reduce 5 to 10 percent of consumed cement, for every one percent of the early hardening nanosil
Increases by 10-20% to the compressive strength of the final product
Increasing the density, increasing the abrasion resistance and reducing the water absorption in the product
Compatibility with various types of concrete additives and lubricants (If using this additive, don't use early hardening nanosil)
HUNAM Artificial Stone Company | With the aim of providing a new generation of robust, beautiful, light and environmentally-friendly construction products, it has been manufacturing polymer artificial stones (Nano Cement Plast). this section, by utilizing the best raw materials and constantly maintaining the quality of products, by offering a completely competitive price (according to special features), it seeks to satisfy its customers.
HUNAM company, with the help of a strong management team, the founder of the tremendous transformations in the artificial stone industry (and Cement Plast) represents the new technologies and techniques and new products.
The company owns modern machinery and new technology and is proud to offer the best and purest artificial stone Nano Cement Plast and engineering artificial stones of the highest quality to the customers using the finest and most domestic materials.
HUNAM artificial stone products can be used extensively in places such as apartments (indoor and outdoor spaces), villas (interior decoration and exterior), hotels, office and engineering offices, banks and hospitals, stores and centers and Commercial large and...
Features of artificial stone Nano Cement Plast flooring and building façade:
High variability (variety in color with the ability to execute various designs and custom)
Light weight is less than natural stones (with a specific gravity of 2,200 kg / m3, from 1,200 to 1,700 kg / m3 and less), which results in lower building weights and consequently reduced earthquake impact on the building.
Ability to absorb artificial stone water less than 2/2 percent (in ceramic and tile)
Limitations on the dimensions of production or installation, such as natural stone
Endurance (tensile strength and pressure) above natural stones
More adhesion with cementitious materials.
High resistance to atmospheric factors as well as color resistance to solar radiation
High resistance to freezing (up to 50 ° C below zero)
High temperature resistance (up to five hundred cycles)
Resistant to expansion and contraction, which causes it to not crack in desert areas.
High strength
Easy and effortless installation and...
No intrusion of darkness in the internal tissue of artificial stone:
In natural stones, it is shiny when installed and has a special effect. this is due to the use of glossy resins on the surface of natural stones. due to atmospheric factors such as sunlight and acid rain, ... after a while, the resins will disappear and the stone will be dark. after the loss of shiny resins, the water absorption of natural stone has increased and because of the absorption of surface water, the soil and contaminants present in the surface, penetrate into the stone, and the stone over time becomes more darken.
With dirt and dust has penetrated the stone, in continuous and discontinuous cavities in stone texture, bacteria, algae and fungi also penetrate and over time, these bacteria and fungi grow. after their death, darkness appears in the tissue of stones.
Because of the very low water absorption (less than 3%), superficial and deep molecular densities, and the absence of continuous and discontinuous cavities in the internal tissue of artificial stones, artificial stones have been excluded from the darkness penetration in the internal tissue of stone.
More adhesion power of artificial stone with building materials:
Due to the non-homogeneity of the coefficient of expansion and contraction of natural stones and concrete and slurry behind the work, over time, the stone is separated from the body, and this will cause damage and ugly appearance in the building.
To solve these problems, there are solutions in natural stones:
Creating a scope behind the rock, which is useless over time due to rust, and after a while, the stone will separate from the body of the building.
Screwing stones from the surface, which makes this case ugly appearance to the building and is not welcomed by consumers.
Artificial stones, due to the concrete base, are more closely aligned with building materials (with slurry materials behind the stones or adhesives used) and have more adhesion power.
Low price artificial stone, in the consumer market compared to natural stones:
Natural stones in the country's consumption market, at a very high price, are available to the compatriots. for example, non-quality stones such as travertine, which formerly known as useless stones, but now, it has been used with cutting, sub, polishing and putty in the body of most buildings.
Lower weight of artificial stones than natural stones:
Volumetric mass of natural stones 2800-2700 kg / m ^ 3
Travertine stones with a mass volume of 2500 kg / m ^ 3
Concrete with a mass volume of 2400-2300 kg / m ^ 3
Volume of artificial stone in the state:
Normal 2200 kg / m ^ 3
Semi-lightweight 1700-1500 kg / m ^ 3
The ultra-light is 1100-500 kg / m ^ 3, which is much lighter than natural stones.
Resistance of artificial stone Nano Cement Plast against frost and heat:
In natural and concrete stones, due to high water absorption and water penetration in the internal tissue of stone and concrete, due to cold weather, penetrated water in the continuous and discontinuous holes is frozen and by freezing the water in their tissue and increasing the volume of ice, natural stone and concrete (street tables and mosaics,...) will crack and fracture. therefore, the use of stones with high water absorption in cold regions is not recommended.
Artificial stones, due to the very low water absorption, have a cold resistance of up to 50 degrees below zero.
Also, natural stone, ceramic tiles and concrete will be fractured due to atmospheric factors and temperature changes (expansion and contraction), but artificial rocks, with cold tolerance up to minus 50 degrees Celsius, as well as a temperature tolerance of up to 350 ° C, and tolerate 500 different temperature cycles, there will be no such problems, due to the cold and also the high temperature as well as temperature tolerances,
Sound and thermal insulation of artificial stones:
Stones with a mass of 1100-500 kg / m ^ 3, in addition to weight loss due to the use of special materials and compounds, acoustic and thermal insulation in the building's structure, and this will save energy.
Also to be insulated against sound up to 40%
Less erosion of artificial stones than natural stones:
Variety of designs, colors and dimensions
Bending strength is higher than concrete and natural stones
The similarities of natural stones, such as marble and granite, can be named
Variety in design and size produced with artificial stones
The ability to use artificial stones in interior and exterior decoration of the building and on any surface
Lower weight than natural stones, which reduces the weight of the building and consequently reduces the impact of the earthquake on the building
Easy installation of artificial stone, and in various ways
More adhesion with cementitious materials (And other building materials)